• Ch Products Flight Sim Yoke Drivers
• Ch Flight Sim Yoke Drivers
• Ch Flight Sim Yoke Drivers Windows 7
• Ch Flight Yoke Driver

CH Products Yoke Modification. The CH Products Flight Sim Yoke is a solid addition to your home flight simulator. Even so, we can modify it a little to make the yoke work more smoothly because the spring tension and the friction within the mechanism can cause you to over-control the airplane. STILL NEED HELP? Want to ask other users with the same product a question? Join the conversation.

CH Products Yoke Modification

The CH Products Flight Sim Yoke is a solid addition to your home flight simulator. Even so, we can modify it a little to make the yoke work more smoothly because the spring tension and the friction within the mechanism can cause you to over-control the airplane. Sometimes you need to make more subtle control inputs.Ideally, when you have the airplane trimmed properly, you can fly with a light touch on the yoke. For example, if you’re over-controlling the airplane during landing, you’ll porpoise down the runway. Well if you don’t do that in real life, it’s embarrassing when it happens in flight simulator.

Our previous video showed how to disassemble the yoke. This video will show the CH Products yoke modification. I’m basically replacing the tension springs with rubber bands. The mod is reversible, so if you decide you don’t like it, you can change it back to the way it was before.

CH Products Yoke Modification

Note: disassembling consumer products may void the manufacturer’s warranty.
We will start by removing the springs. There is continuous tension on the spring, so push it down onto the pylon. Then remove the screw and washer… and carefully unhook the spring. Reattach the screw. Unhook the other end of the spring from the shaft. Repeat on the other side to remove the second spring. This cable is held in place with a small zip tie. Carefully snip it off. We’re going to use the hole that the zip tie was in…but we’re going to need one on the other side too. Here’s the existing hole, and now we’re drilling one in the same place on the other side. This is a one eighth inch drill bit. Just removing the little plastic shavings here.

Ch Products Flight Sim Yoke Drivers

Now we have our own little zip ties for the next step, and rubber bands. Insert the zip tie through the hole. Take two rubber bands and loop them over themselves like this. Connect the zip tie to one end of the rubber bands like this. Then stretch the rubber band over the pylon. Repeat on the other side. Notice I’m holding the yoke handle when I loop the rubber bands over the pylon.

Everything is looking good so far so let’s tighten up the zip ties. Loosen the rubber bands, cinch up the zip tie, then loop the rubber bands over the pylon again. Here’s the opposite side. Try not to get the rubber bands twisted too much. Snip off the ends of the zip ties.

Finishing Steps

Now you might ask, isn’t there a simpler way? If you look at how the shaft is constructed, you’ll notice we can simply loop these rubber bands on the opposite horn like this and loop the other rubber bands on the other side. Well that does work, but not very well. The rubber bands tend to rub against each another and make a banjo sound. I’m assuming you don’t want your yoke to sound like a banjo, so that’s out.

Ch Flight Sim Yoke Drivers

Remember this lever needs to be seated correctly on the bottom of the shaft, and the sleeves need to set in the grooves on the back of the unit. Finally, this wiring harness was disconnected from the mini-levers that we removed in the previous video. We don’t want it flopping around, so we attached it to these other wires with a zip tie, and everything is tucked away nicely.

The CH Products yoke modification is complete! Now the yoke has a better response to those subtle little control inputs that we tend to use when the airplane is trimmed for cruise flight, or any time a soft touch is necessary.

The Aspiring Pilot's Introduction to Flight Simulation Hardware

Whether your preferred plane is commercial or private, the Saitek Pro Flight Yoke with included Throttle Quadrant is a must-have for beginning and advanced flight simulation enthusiasts. Delivering realistic and precise control while enhancing muscle memory, the Yoke and Throttle Quadrant with five total axes simulate what it feels like to truly fly an aircraft. Saitek's Pro Flight equipment is modular and interchangeable, and the Yoke anchors a comprehensive flight sim setup. There's no better way to begin your flight sim experience than with Saitek, the market leader in high-performance flight simulation hardware.

Ch Flight Sim Yoke Drivers Windows 7

Simple Plug-and-Play Installation

Ch Flight Yoke Driver

The Throttle Quadrant connects to the Yoke via PS/2 connector cable, and the Yoke directly connects to a USB port on your PC or Mac. You can then simply load your favorite sim, set controls in the sim's options menu, and you're all set for virtual flight without the need to load drivers or install extra software. The Yoke's four-foot-long USB cable frees you to place the controls where they're most convenient for you.